- #External spi programmer serial#
- #External spi programmer drivers#
- #External spi programmer software#
- #External spi programmer series#
through an SPI / QSPI peripheral controller), too. The J-Link is connected to the debug interface of the CPU and the flash is connected to the CPU (e.g. In Indirect Mode, the flash is programmed indirectly through the CPU. Further information regarding this as well as the interface / protocol description are available, please refer to the J-Flash SPI information page.Īdditional adapter / interface is required on the hardware
The J-Link is connected directly to the SPI flash and communicates with the SPI flash itself. In Direct Mode, the flash is programmed directly via J-Link using the SPI protocol, no CPU / MCU in between. Which way is the right one for you depends on your requirements or your hardware setup.
#External spi programmer software#
The J-Link software supports programming most common SPI / QSPI flashes in two different ways. They are used as additional data memory or even replace the internal flash.
#External spi programmer serial#
Looking at this post from AVRFreaks will provide you with code for some of Atmels AT45xxxx serial flash chips.The popularity of external SPI flashes has grown and becomes more and more attractive on custom hardware. Hence, since all external flash memories does not have the same instruction set, you need to write a customized application for this one.ĮDIT: Being a follow up, I would really recommend one of Atmels own SPI flash memories, since most of them already has written open available code for them. Under 7.2 Instructions chapter in the datasheet you can see all the SPI commands you can send to it. The chip needs SPI calls for write, read, change sector, data size etc. I have never heard of any other tools talking SPI directly to such a chip, and I think it is impossible since "all" chips require different calls for different operations.
I've also seen specialized tools for loading EEPROM's over I2C directly, but not flash and not SPI specifically. It might take a bit of work to "script" it, but it would let you do the job probably. that lets you perform somewhat arbitrary serial interactions directly to a chip using SPI, I2C, or UART communication. I bet you could do it with a Bus Pirate without going through your MCU. There are 6-pin, 10-pin and 14-pin versions of the cable available to suit a range of applications.
#External spi programmer series#
They manufacture and sell a series of quick connect programming cables that have pogo pins that engage the special footprint on the board. One nice solution for this is to place a small set of pads in a special footprint defined by a company called TagConnect. Sometimes it can be beneficial to be able to connect a programmmer to a target board without having to add a programming header. Their more expensive device called the Forte is able to do more things because it has more target interface pins. It is a more cost effective solution than the above unit but not quite as flexible. I have one of these devices specifically for programming Atmel MCUs and various types of SPI Flash devices. The Presto is able to do various types of SPI and I 2C devices including SPI Flash devices.
make all those GPIOs as inputs).Ī second choice to also consider is the USB programer from ASIX. An even more clever scheme is to add a "programming enable" input to the MCU that makes the software disconnect all the SPI I/Os from the SPI Flash chip (i.e. Alternate methods could include adding a MUX or analog switches in the driven interface lines. The programmer would connect on the SPI flash side of the series resistors. The simplest way to do this is to put series resistors in the MCU driven lines between the MCU and the SPI Flash.
#External spi programmer drivers#
The main strategy for the design is to find a simple way to isolate the SPI interface drivers in your MCU system so that they do not interfere with the drivers in the SPI programming pod. DediProg has application information bulletins available to help with correct design for in circuit use.
They even sell an adapter clip that can attach into the SOW-16 package without having to design in a separate programming header on your board. This USB connected device can program in circuit if you design your board correctly. One choice is the programmer from DediProg. This also known as in-system-programming (ISP). If you are simply looking for a way to program the Winbond SPI flash with "pre-loaded" data that your microcontroller would read for use when it is running then what you will want to look into is a programmer that can do in-circuit programming of the SPI Flash chip.
0 kommentar(er)
